Harness identification and application
Harness Identification and Application
Table of Contents
HRN-BD16S4 — Discontinued | |||
HRN-BS16T2 — Discontinued HRN-BT16T2 — Discontinued HRN-BE16T2 — Discontinued HRN-BF16T2 — Discontinued HRN-BG16T2 — Discontinued | HRN-DC09T2 — Discontinued HRN-DR09T2 — Discontinued HRN-DS09T2 — Discontinued | HRN-CW08A4— Discontinued HRN-CE10A2— Discontinued HRN-CK10A2— Discontinued | HRN-CW03S3— Discontinued HRN-RW03S4— Discontinued |
! IMPORTANT:Â Only use Geotab telematics devices with Geotab-approved harnesses acquired from Geotab-authorized channels. Use of non-Geotab harnesses from unauthorized channels may cause serious safety risks, including fire, and may lead to serious personal injury and/or damage to the vehicle. |
Introduction
This document identifies all the harnesses available in MyAdmin, and the harnesses available by special order. This document also provides an overview of each harness:
- A description of the harness (as seen in MyAdmin);
- The length of the harness;
- The purpose of the harness;
- The GO device supported by the harness; and
- The renamed or replaced harness.
Naming Conventions
In June 2014, we updated the harness naming convention. This section outlines the new naming convention and provides definitions for each character or group of characters.
Harnesses all start with an HRN prefix followed by 6-character names, as defined below. All characters are alphanumeric and, to avoid confusion, no I’s or O’s are used.
Examples:
- HRN-DS09T2
- DÂ represents a Deutsch connector
- SÂ represents a Standard OBD, Deutsch, or FMS connector
- 09Â represents 9 pins / wires
- TÂ represents a T-harness
- 2Â represents a length in the range of 12-24 inches or 30-60 cm
- HRN-BS16S4
- BÂ represents OBD type connectors
- SÂ represents a Standard OBD, Deutsch, or FMS connector
- 16Â represents 16 pins / wires
- SÂ represents a straight harness
- 4Â represents a length in the range of 36-48 inches or 120-152 cm
- HRN-CW03S3
- CÂ represents a Custom harness
- WÂ represents a Harness with exposed wires
- 03Â represents 3 pins / wires
- SÂ represents a Straight harness
- 3Â represents a length in the range of 24-36 inches or 60-90 cm
Harness Naming — Table of Definitions
The following table helps to identify the harnesses.
Category | Family | Connections | Type | Length | Sub-Type | ||||||
Defined broad category of harnesses (Deutsch, OBDII, European, custom, etc.) | Defines family of harnesses which can be common, manufacturer specific, proprietary, etc. | Number of pins used or specific connections connecting up to an asset | Harness Type (i.e. straight, split, etc.) | Length of harness between the vehicle connector and GO device | Harness Sub-Type for different variants of the same harness | ||||||
Code | Definition | Code | Definition | Code | Definition | Code | Definition | Code | Definition | Code | Definition |
A | Auxiliary connector | A | DAF-specific connector | 03 | 3 pins/wires | A | Adapter harnesses | 1 | 0-30 cm (0-12 inches) | F | Flat cable |
B | ODB-type connectors | C | Komatsu-specific, and Caterpillar-specific connectors | 04 | 4 pins/wires | K | Kit contains more than one part | 2 | 30-60 cm (12-24 inches) | U | Customer Specific |
C | Custom harness | D | Delphi-specific connector | 06 | 6 pins/wires | T | T-harnesses | 3 | 60-90 cm (24-36 inches) | 1-9 | Numeric code for harness updates |
D | Deutsch connectors | E | Mercedes connector and Volvo/Mack Truck specific connectors | 08 | 8 pins /wires | S | Straight harnesses | 4 | 90-120 cm (36-48 inches) | A | Region specific manufacturing, but no functionality differences |
E | European Imported Heavy Goods vehicle style connectors | F | Mercedes & Citroen, Peugeot, Renault, Fiat specific connectors | 09 | 9 pins/wires | Y | Connects up to two or more different connectors | 5 | 120-152 cm (48-60 inches) | ||
G | Global | G | BMW & Volkswagen, Audi, Seat, Skoda specific connectors | 10 | 10 pins/wires | ||||||
R | Rugged | H | Hino-specific connector | 11 | 11 pins/wires | ||||||
U | Dual protocol, extension harness | I | Isuzu-specific connector | 12 | 12 pins/wires | ||||||
K | Mack Truck specific connectors | 14 | 14 pins/wires | ||||||||
M | Multiple connectors | 16 | 16 pins/wires | ||||||||
N | Navistar | 20 | 20 pins/wires | ||||||||
P | Sprinter PSM connectors | 21 | 21 pins/wires | ||||||||
R | Threaded type 9-pin Deutsch connector | 24 | 24 pins/wires | ||||||||
S | Standard OBD, Deutsch, or FMS connector | DM | Delphi Molex Connectors | ||||||||
T | Tesla-specific connector | RC | Rugged CAT Connectors | ||||||||
U | Fuso-specific connector | ||||||||||
V | Iveco-specific connector | ||||||||||
W | Harness with exposed wires | ||||||||||
X | IOX | ||||||||||
Z | TUG-specific connector |
Installation Notes for All Harnesses
! IMPORTANT:Â For heavy-duty trucks, always use a vehicle-specific harness when offered by Geotab or the vehicle manufacturer (see Harness Identification and Application [PUB]Â and Harness Assessment Cheat Sheet GUIDE V2.0 [PUB]). Where a heavy-duty truck-specific harness is not offered by Geotab or the vehicle manufacturer, use the adapter harness (HRN-CG13S1) for any 16-pin (OBDII) installation method to avoid possible GO device damage. |
✱ NOTE: If a longer length is required to facilitate installation, connect a straight harness to a T-harness or another straight harness — where indicated below. The total harness length must not exceed 2 meters (or 6.5 feet). |
✱ NOTE: Regardless of the length, two T-harnesses CANNOT connect to each other. Connecting two T-harnesses, or any two harnesses that exceed 2 meters, compromises the integrity of the data and may cause issues with the vehicle’s Engine Control Unit (ECU). |
OBD Harnesses
HRN-BS16S4MyAdmin Details Description: OBDII Extension harness for the GO device. Replaces HRN-INSTALLPACKV2. Further Information Replaces:Â HRN-INSTALLPACKV2 Length: 100 cm / 39 inches Purpose: Used to extend the placement of the GO device. Required on vehicles where the ALDL (OBD vehicle connection) is located in an area that may cause the GO device to impede the driver. Also required for vehicles where the recess of the ALDL location prevents the GO device from connecting properly. Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-BS16S4FMyAdmin Details Description: Flat OBDII extension harness for GO devices with low profile connectors Further Information Length: 60 cm / 24 inches Purpose: Used to connect the GO device to an OBD port that is covered by a panel — available in vehicles with low-profile connectors. Max length of connected cables: 2 meters / 6.5 feet |
HRN-BS16S5MyAdmin Details Description: OBDII Extension harness for the GO Device — 150 cm in length. Further Information Length: 150 cm / 59 inches Purpose: Used to extend the placement of the GO device. Required on vehicles where the ALDL (OBD vehicle connection) is located in an area that may cause the GO device to impede the driver. Also required for vehicles where the recess of the ALDL location prevents the GO device from connecting properly. Max length of connected cables: 2 meters / 6.5 feet |
HRN-BS16T2Â DiscontinuedMyAdmin Details Description: OBDII T-harness for the GO device. Replaces HRN-EZT. Further Information Replaces:Â HRN-EZT Length: 50 cm / 20 inches Purpose: To move the GO device under the dashboard and out of sight while leaving the OBD connector exposed. Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-BT16T2Â DiscontinuedMyAdmin Details Description: OBDII Extension T-harness for the GO device. Required globally for Ford Transit Connect and Ford Transit Full Size Vans. May be required in other Ford vehicles as well as Land Rover and Jaguar; and Asian vehicles such as Honda, Mitsubishi, Nissan, Toyota, Kia, and Hyundai. Further Information Length: 50 cm / 20 inches Purpose: With vehicle-specific OBD connectors, this T-harness connects to vehicles found in Global markets. It allows the OBD connector to remain exposed and with the GO device installed under the dashboard and out of sight. It is required for many European vehicles, some of which are in North America. These include the Ford Focus, B-Max, C-Max, S-Max, Fiesta, Mondeo (Model Year 2014 and earlier), Galaxy, Kuga, EcoSport, Transit Connect, and 2016 Ford Escape. Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-BE16T2 DiscontinuedMyAdmin Details Description: OBDII T-harness for the GO device. Mercedes-specific connector. Commonly used for Sprinters for NA and Europe — that DO NOT connect to a Parametric Special Module (PSM) — and Volvo and Mack NA Trucks (2014 and 2015 MY). Further Information Length: 50 cm / 20 inches Purpose: With a Mercedes specific OBD connector, this T-harness connects to Mercedes Sprinters commonly found in Global markets. It is NOT used to connect to a PSM in the vehicle. It is also used to connect to North American Volvos and Mack Trucks (2014 and 2015 MY). Allows the OBD connector to remain exposed with the GO device installed under the dashboard and out of sight. Max length of connected cables: 2 meters / 6.5 feet |
HRN-BF16T2Â DiscontinuedMyAdmin Details Description: OBDII Extension T-harness for the GO device. Primarily for European markets. Special connectors for Mercedes Benz and also Citroen, Peugeot, Renault, Dacia, FIAT, Alfa Romeo, and certain Iveco vehicles. Further Information Length: 50 cm / 20 inches Purpose: With vehicle-specific OBD connectors, this T-harness connects to European-manufactured vehicles found in Global markets. It is NOT used to connect to a PSM in the vehicle. Allows the OBD connector to remain exposed with the GO device installed under the dashboard and out of sight. Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-BG16T2Â DiscontinuedMyAdmin Details Description: OBDII Extension T-harness for the GO device. Primarily for European markets. Special connectors for VW and Audi Group (VAG) vehicles, and also for certain BMW vehicles. Further Information Length: 50 cm / 20 inches Purpose: With vehicle-specific OBD connectors, this T-harness connects to European-manufactured vehicles found in Global markets including Audi, Seat, Skoda, Volkswagen, and certain BMW models. Allows the OBD connector to remain exposed with the GO device installed under the dashboard and out of sight. Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-BU16Y5MyAdmin Details Description: OBDII harness for the GO device. Special vehicle connector to receive engine data from Mitsubishi Fuso (medium duty) vehicles. Further Information Replaces:Â HRN-EZFUSO Length: 130cm / 51 inches Purpose: Used specifically for Mitsubishi Fuso (medium duty) vehicles to allow capture of VIN and odometer. Requires connection to Fuso connector in addition to standard OBD port. Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-GS16K2
IMPORTANT:Â Geotab prohibits the use of the 16-pin universal harness in North American Volvo/Mack 2019+ trucks when using a version 9 GO device, due to a known interoperability issue. Geotab has a specific harness intended for version 9 installations (HRN-CM24Y1 with HRN-CE10A2 or HRN-CS14S21 14-pin connector).
MyAdmin Details
Description: Universal OBDII T-Harness Kit for the GO device. Multi-adapter kit consisting of a T-harness (HRN-BM16T2) and 12 different mounting adapters for use in most light-duty, medium-duty, and heavy-duty vehicles, and is compatible with most models globally.
Further Information
Documentation:Â Support Document (goo.gl/tNoQh4), Installation Instructions (goo.gl/1Vninm)
Replaces: HRN-BE16T2, HRN-BG16T2, HRN-BF16T2, HRN-BS16T2, HRN-BT16T2
Length: 60 cm / 24 inches
Purpose: Used to extend the placement of the GO device. Required on vehicles where the ALDL (OBD vehicle connection) is located in an area that may cause the GO device to impede the driver. Also required for vehicles where the recess of the ALDL location prevents the GO device from connecting properly. The 12 different mounting adapters allow for installation in different vehicles makes and/or models. Region specific, but no functionality differences
Max length of connected cables:Â 2 meters / 6.5 feet
Deutsch Connector Harnesses
HRN-DR09T2Â DiscontinuedMyAdmin Details Description: 9-pin heavy-duty T-Harness for installations where the Deutsch connector needs to remain available for other applications and is a THREADED dash mount style. Replaces HRN-CD9TBHD. Further Information Replaces: HRN-CD9TBHD Length: 60 cm / 24 inches Purpose: To move the GO device under the dashboard and out of sight while leaving the Deutsch connector exposed. This harness is different from a standard 9-pin Deutsch connector harness because it uses a threaded connector. The threaded connector is becoming more common within the heavy-duty market. The following vehicles require the HRN-DR09T2 harness:
The following vehicles do not require the HRN-DR09T2 harness:
Max length of connected cables: 2 meters / 6.5 feet |
HRN-DS09S4MyAdmin Details Description: 9-pin straight harness for North American heavy-duty Deutsch connector installations. Replaces HRN-C9HD. Further Information Replaces: HRN-C9HD Length: 100 cm / 39 inches Purpose: Straight harness used to move the GO device out of the way of the driver. Max length of connected cables:Â 2 meters / 6.5 feet | l |
HRN-DS09T2 DiscontinuedMyAdmin Details Description: 9-pin heavy-duty T-Harness for installations where the Deutsch connector needs to remain available for other applications. Further Information Replaces: HRN-CD9THD Length: 60 cm / 24 inches Purpose: To move the GO device under the dashboard and out of sight while leaving the Deutsch connector exposed. This harness has a standard 9-pin Deutsch connector. Max length of connected cables: 2 meters / 6.5 feet |
HRN-DS06S4MyAdmin Details Description: 6-pin straight harness for North American heavy-duty Deutsch connector installations. Replaces HRN-D6HD. Further Information Replaces: HRN-D6HD Length: 100 cm / 39 inches Purpose: Straight harness used to move the GO device out of the driver’s way. This harness has a standard 6-pin Deutsch connector and does NOT leave the Deutsch connector exposed. Max length of connected cables: 2 meters / 6.5 feet |
HRN-DS06T2MyAdmin Details Description: 6-pin heavy-duty T-Harness for installations where the Deutsch connector needs to remain available for other applications. Replaces HRN-D6THD. Further Information Replaces: HRN-D6THD Length: 60 cm / 24 inches Purpose: To move the GO device under the dashboard and out of sight while leaving the Deutsch connector exposed. This harness has a standard 6-pin Deutsch connector. What changed: The harness is now 60 cm in length (24 inches) allowing for GO device installation without an install pack. Max length of connected cables: 2 meters / 6.5 feet |
HRN-DC09T2Â DiscontinuedMyAdmin Details Description:Â Special harness for CAT off-road vehicles. Verify that the vehicle does not use a standard 9-pin connector. Replaces HRN-TCATHD. Further Information Replaces:Â HRN-TCATHD Length:Â 30 cm / 12 inches Purpose: To move the GO device under the dashboard and out of sight while leaving the Deutsch connector exposed. Max length of connected cables:Â 1 meter / 3.3 feet |
HRN-DC14S2MyAdmin Details Description:Â 14-pin harness for CAT vehicles 2016+. IP67 rated when used along with GO RUGGED (harness revision 2 & 3 ONLY). Further Information Length: 30 cm Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-GR09K1MyAdmin Details Description: Universal Rugged Heavy-Duty T-Harness Kit (IP67) Further Information Documentation: Support Document (goo.gl/mFhnAu), Installation Instructions (goo.gl/hzHSX4) Length: 25 cm / 9.8 inches Purpose: Used to extend the location of the GO device. This harness is built to IP67 standards for protection against dust and water. Required on vehicles where the 9-pin diagnostic port is located in an area where it is exposed to the elements. The 4 different mounting adapters allow for installation in different heavy-duty vehicles makes/models. Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-GS09K2MyAdmin Details Description: Universal Heavy-Duty T-Harness Kit for the GO device. Multi-adapter kit consisting of a 9-pin T-harness (HRN-DM09T2) and ​4 different mounting adapters (Adapter 1 pre-installed) for use in most medium and heavy-duty international vehicles. Eliminates the need to know vehicle information in advance. Further Information Documentation: Support Document (goo.gl/8UPnAj), Installation Instructions (goo.gl/3I42wy) Replaces: This harness replaces HRN-DR09T2 and HRN-DS09T2. Length: 68 cm / 27 inches Purpose: Used to extend the location of the GO device. Required on vehicles where the 9-pin diagnostic port is located in an area that may cause the GO device to impede the driver. Also required for vehicles where the recess of the 9-pin diagnostic port location prevents the GO device from connecting properly. The 4 different mounting adapters allow for installation in different medium and heavy-duty vehicles makes and/or models. Max length of connected cables: 2 meters / 6.5 feet |
Custom Harnesses
HRN-BS04A1MyAdmin Details Description: Adapter harness needed in conjunction with HRN-DS09T2, HRN-DR09T2 or HRN-GS09K2 on 2017+ Kenworth and Peterbilt trucks for enhanced engine data support. Required for GO7 and GO8 devices only. It’s for the 2017+ Kenworth and Peterbilt trucks using GO7 and GO8 devices. HRN-BS04A1 not required for GO9. Further Information Requires: HRN-GS09K2 Length: 6.3 cm / 2.5 inches Purpose: Used specifically for 2017+ Kenworth and Peterbilt trucks with Paccar engines MX13/MX15 to obtain enhanced engine data. Max length of connected cables: 2 meters / 6.5 feet |
HRN-BF11A1MyAdmin Details Description:Â Custom proprietary harness for enhanced engine data support on select Fiat/Chrysler vehicles in LatAm. Further Information Length: 20 cm Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-CM24Y1MyAdmin Details Description: GO device harness for custom installs. Molex connectors for 2 OBD and one J1939 connection points. Further Information Replaces: HRN-INTCPDUAL Length: 20 cm Purpose: For custom installs that require multiple connection points to access engine data and engine protocols. The harness consists of an ALDL connector at one end for the GO device, a white 6-pin Molex connector for one OBD connection, a black 12-pin Molex connector for a second OBD connection, and a second 6-pin Molex connector for a J1939 connection (GO7 & GO8 only). Max length of connected cables: 2 meters / 6.5 feet |
HRN-CW08A4 DiscontinuedMyAdmin Details Description: 8-wire pigtail adapter for vehicles with connectors that are not supported on any other harness. Requires HRN-CM24Y1. Further Information Requires: HRN-CM24Y1 PIN Definition: Red - Power Source, Black - Vehicle ground, Blue - J1939+/CAN High, White - J1939-/CAN Low, Brown - J1850-/J1708+, Green - J1850+/J1708-, Orange - ISO K-line, Grey - ISO L-line Length: 80 cm Max length of connected cables:Â 2 meters / 6.5 feet | |
HRN-CW08K4MyAdmin Details Description: Custom 8-wire harness kit for vehicles with no supported connectors. Requires HRN-CM24Y1. The custom kit contains the harness and a fuse kit. Further Information Replaces: HRN-CW08S4 PIN Definition: Red - Power Source, Black - Vehicle ground, Blue - J1939+/CAN High, White - J1939-/CAN Low, Brown - J1850-/J1708+, Green - J1850+/J1708-, Orange - ISO K-line, Grey - ISO L-line Length: 80 cm Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-CH06A2MyAdmin Details Description: Custom proprietary HINO FMS adapter. Requires HRN-CM24Y1. Further Information Requires: HRN-CM24Y1 Length: 30 cm / 12 inches Max length of connected cables: 2 meters / 6.5 feet |
HRN-CH10A2MyAdmin Details Description: Custom 10-pin Hino FMS adapter (2019+). Requires HRN-CM24Y1. Further Information Requires: HRN-CM24Y1 Length: 30 cm / 12 inches Max length of connected cables: 2 meters / 6.5 feet |
HRN-CE04A4MyAdmin Details Description:Â Custom proprietary adapter for Volvo vehicles in LatAm and EU. Requires HRN-CM24Y1. Further Information Requires: HRN-CM24Y1 Length: 80 cm Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-CE10A2Â DiscontinuedMyAdmin Details Description:Â Custom adapter for Volvo vehicles in North America. Requires HRN-CM24Y1. Further Information Requires: HRN-CM24Y1 Length: 30 cm Max length of connected cables:Â 2 meters / 6.5 feet | |
HRN-CE10K2MyAdmin Details Description: Custom harness kit for Volvo/Mack vehicles, 2019 or newer, in North America. Requires HRN-CM24Y1. The custom kit contains the harness and a fuse kit. Documentation: Support Document (gtb.page.link/VcAu). Installation Instructions:  gtb.page.link/euh3 and  gtb.page.link/krdH. Further Information Replaces: HRN-CE10A2 and SPR-VOVKIT Length: 30 cm Max length of connected cables: 2 meters / 6.5 feet |
HRN-CG13S1
MyAdmin Details
Description: 13-pin custom adapter to be used with HRN-GS16K2 Universal Harness Kit.             Â
Further Information
Length: 10 cm / 4 inches
Purpose: An adapter to remove the power transient from a vehicle interface protocol.
Max length of connected cables:Â 2 meters / 6.5 feet
HRN-CG04T3MyAdmin Details Description: 4-pin custom adapter to be used for VW only.              Further Information Length: 60 cm / 24 inches Purpose: An adapter to remove the power transient from the VW vehicle interface protocol. Max length of connected cables: 2 meters / 6.5 feet HRN-CI04A2MyAdmin Details Description: Custom Isuzu FMS adapter (2017+). Requires HRN-CM24Y1 and Isuzu’s optional FMS kit. Further Information Requires: HRN-CM24Y1 Purpose: This harness is only meant for diesel vehicles and supported engine data from the FMS port inside the vehicle Length: 30 cm / 12 inches Max length of connected cables: 2 meters / 6.5 feet |
HRN-CK10A2 DiscontinuedMyAdmin Details Description:Â Custom adapter for Mack vehicles in North America. Requires HRN-CM24Y1. Further Information Requires: HRN-CM24Y1 Length: 30 cm Max length of connected cables:Â 2 meters / 6.5 feet | |
HRN-CK10K2MyAdmin Details Description: Custom harness kit for Mack vehicles, 2018 or older, in North America. Requires HRN-CM24Y1. The custom kit contains the harness and a fuse kit. Further Information Replaces: HRN-CK10A2 Length: 30 cm Max length of connected cables:Â 2 meters / 6.5 feet | |
HRN-CP04A2MyAdmin Details Description:Â PSM module connection for Mercedes Sprinters (907 and 910 Chassis) for Global markets (requires HRN-CM24Y1). Further Information Requires: HRN-CM24Y1 Length: 60 cm / 24 inches Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-CS14S21MyAdmin Details Description: 14-pins connector harness for heavy-duty applications (Refer to the Vehicle Specific Installation document for specific instructions). This is used for any vehicles with an RP1226 diagnostic connection. Further Information Length: 60 cm / 24 inches Max length of connected cables: 2 meters / 6.5 feet |
HRN-CT06A1MyAdmin Details Description: Custom adapter for Tesla vehicles. Requires HRN-CM24Y1 and XXX.19.XX GO device firmware or higher. Further Information Requires: HRN-CM24Y1 Length: 10 cm Max length of connected cables: 2 meters / 6.5 feet |
HRN-CT06A11MyAdmin Details Description: Custom Tesla Model S (post 2016) & X adapter (requires HRN-CM24Y1) Further Information Requires: HRN-CM24Y1 Length: 20 cm / 7.9 inches Max length of connected cables: 2 meters / 6.5 feet |
HRN-CT20T1MyAdmin Details Description:Â Custom Tesla Model 3 harness (2018) Further Information Requires: GO9 Device Length: 30 cm / 12 inches Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-CT20T11MyAdmin Details Description:Â Custom Tesla Model 3 harness (2019+) Further Information Requires: GO9 Device Length: 30 cm / 12 inches Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-CT06S2MyAdmin Details Description:Â Custom Tesla Model S/X harness (2015). Further Information Requires: GO9 Device Length: 30 cm /12 inches Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-UP21Y2MyAdmin Details Description: PSM module connection for Mercedes Sprinters for global markets. Requires HRN-CM24Y1. Further Information Replaces:Â HRN-SPRPSM Length: 20 cm Purpose: Used for PSM module connection on Mercedes Sprinters for global markets in conjunction with HRN-CM24Y1. Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-RMRCA1MyAdmin Details Description: CAT specific adapter for the GO RUGGED device (requires HRN-GR09K1) Further Information Requires: HRN-GR09K1 Length: 10 cm Max length of connected cables: 2 meters / 6.5 feet |
HRN-CW03S3 DiscontinuedMyAdmin Details Description: Custom 3-wire harness for the GO device — PWR, GND, IGN. Replaces HRN-2WCP for GO6 which cannot take advantage of the IGN wire. Further Information Documentation: Support Document (goo.gl/VEvruL) Replaces: HRN-3WCP Length: 90cm / 36 inches Purpose: Used for installation in vehicles or assets where no engine data is available. Max length of connected cables: 2 meters / 6.5 feet | |
HRN-CW03K3MyAdmin Details Description: Custom 3-wire harness kit. The custom kit contains the harness and a fuse kit. Further Information Replaces: HRN-CW03S3 Length: 90 cm Max length of connected cables: 2 meters / 6.5 feet |
HRN-RS12S2MyAdmin Details Description: 12-way Amphenol weather resistant rugged harness for GO RUGGED — PWR, GND, IGN. Further Information Length: 30 cm / 12 inches Purpose: Used to move the GO RUGGED out of the driver’s way. Geared towards adverse weather conditions, does not leave connector exposed. Max length of connected cables: 2 meters / 6.5 feet |
HRN-RX06S4MyAdmin Details Description: 6-way IOX harness for GO RUGGED to provide IOX add-on support. The gray connector is weather resistant. Further Information Length: 100 cm / 39 inches Purpose: Used for installation in vehicles or assets where auxiliary is needed. Max length of connected cables:Â 1 meter / 3.2 feet |
HRN-RW03S4 DiscontinuedMyAdmin Details Description: 3-wire harness for GO RUGGED — PWR, GND, IGN. Further Information Length: 100 cm Max length of connected cables: 2 meters / 6.5 feet | |
HRN-RW03K4MyAdmin Details Description: 3-wire harness kit for GO RUGGED. The kit contains the harness and a fuse kit. Further Information Replaces: HRN-RW03S4 Length: 100 cm Max length of connected cables:Â 2 meters / 6.5 feet | |
HRN-RW08K1MyAdmin Details Description: 8-wire harness kit for GO RUGGED. The kit contains the harness and a fuse kit.Further InformationLength: 16.5 cmMax length of connected cables:Â 2 meters / 6.5 feet |
HRN-RW04S4MyAdmin Details Description: Differential harness used for negative battery disconnect / oil pressure switch / negative output ignition for the GO RUGGED device. Required for ground service equipment. Further Information Length: 100 cm Purpose: All Equipment with  Ground Disconnect on Asset and or NON ECM with No true Ignition Max length of connected cables: 2 meters / 6.5 feet | |
HRN-RZ04T4MyAdmin Details Description: Kubota gas engine interface harness for the GO RUGGED device. Required for ground service equipment. Further Information Length: 110 cm Purpose: Kubota Type Engine  MA-40-36 (Ground Service Equipment). Max length of connected cables: 2 meters / 6.5 feet | |
HRN-RZ04S4MyAdmin Details Description: Ford EDI TUG engine interface harness for the GO RUGGED device. Required for ground service equipment. Further Information Length: 110 cm Purpose: FORD Model type Engine MSG-425.2.5 liter (Ground Service Equipment). Max length of connected cables:Â 2 meters / 6.5 feet | |
HRN-RW03S5MyAdmin Details Description: Pulse harness for engines not reporting ignition / RPM for the GO RUGGED device. Required for ground service equipment. Further Information Length: 122 cm Purpose: NON ECM with NO true Ignition Using Low voltage/ Primary side of ignition coil. Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-RW07T1MyAdmin Details Description: Tri-pin connector harness for vehicles without diagnostic ports (off-road vehicles only). Requires a GO RUGGED. Further Information Length: 20 cm Max length of connected cables:Â 2 meters / 6.5 feet |
SPR-RELAYKITMyAdmin Details Description: Driver ID Relay kit for GO4v3, GO6, GO7 and GO8. Requires professional installation by a licensed automotive electrician/mechanic. Further Information Documentation: Support Document (goo.gl/iwUJfq) Replaces: HRN-RELAYKIT Length: 60 cm / 24 inches Purpose: Used as standalone on GO4V3 or in conjunction with the NFC driver ID on GO6, GO7 or GO8. Driver ID keys drive a relay. Requires professional installation by a licensed automotive electrician/mechanic. GO Devices supported: GO4v3, GO6, GO7, GO8 Installation Instructions: Please refer to the SPR-RELAYKIT Installation instructions. |
European Heavy Goods Vehicle Harnesses
HRN-ES12S1MyAdmin Details Description: OBDII harness for the GO device. Connects to the FMS connector primarily for European heavy-duty vehicles. Further Information Replaces:Â HRN-FMSSTA Length: 30 cm / 12 inches Purpose: Straight harness used to connect directly to the dedicated Telematics port common on European vehicles. Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-EE14S1MyAdmin Details Description: Mercedes diagnostic connector. Used on older generation medium duty trucks and buses. Replaces HRN-EU14P. Further Information Replaces: HRN-EU14P Length: 30 cm / 12 inches Purpose: To move the GO device under the dashboard and out of sight. Like all harnesses, the HRN-EE14S1 provides power to the GO device and allows the GO device to record engine data for specific vehicles that require this type of connector. Max length of connected cables: 1 meter / 3.3 feet |
HRN-EA16S1MyAdmin Details Description: Diagnostic connector designed for European markets, primarily for the DAF Euro 3 (up to 2006). Replaces HRN-EU16P. Further Information Replaces: HRN-EU16P Length: 30 cm / 12 inches Purpose: To move the GO device under the dashboard and out of sight. Like all harnesses, the HRN-EA16S1 provides power and engine data for specific vehicles that require this type of connector. Max length of connected cables: 1 meter / 3.3 feet |
Special Order Harnesses
The following harnesses are only available by special order. Long lead times may exist. Contact your account Manager to determine prices, lead times, and to ensure it is the required harness.
HRN-BD16S4 DiscontinuedMyAdmin Details Description: Custom order third-party device harness. No longer used for Valor implementations. Not available in MyAdmin. Further Information Length: 100 cm / 40 inches Purpose: Harness used in custom situations. Please discuss with Geotab Support, or your Account Manager to determine if harness is appropriate. Max length of connected cables: 1 meter / 3.3 feet |
HRN-BD16S5Description: Custom order third-party device harness. Not available Length: 130.5 cm / 51.5 inches Purpose: Uses OEM connector instead of using EZT bracket. Max length of connected cables:Â 2 meters / 6.5 feet |
HRN-CMDMY3Description: Custom order third-party device harness. Not available Length: 80 cm Purpose: Designed for OEM Freightliner walk-in van chassis with Gas engines, 2009, and newer year models installed with GO4 units. Also requires an HRN-BD16S4. Includes an ALDL connector on one end to connect the HRN-E1 harness, a 6-pin Molex connector for OBD connections. Max length of connected cables: 2 meters / 6.5 feet |
Installation Accessories
The following items are commonly ordered with harnesses to properly secure the GO devices in the vehicle.
SPR-INSTALLBAGMyAdmin Details Description:Â Mounting bracket and material for the GO device. For installation purposes, the package includes 2 zip seals, 2 screws, and double-sided tape for the bracket. Further Information Purpose: Provides installers with mounting material to ease GO device installation. Installing the mounting bracket: Use the screws or double- sided tape to affix the bracket to the vehicle. Place the GO device in the bracket as shown in the image. |
SPR-NFCBRACKETMyAdmin Details Description: Mounting bracket and holder for IOX-NFCREADER. For installation purposes, the package includes 2 screws and double-sided tape for the bracket. Further Information Purpose: Provides installers with a replacement mounting bracket for the NFC Reader. Installing the mounting bracket: Use the screws or double-sided tape to affix the bracket to the vehicle. |
SPR-BSFBKTMyAdmin Details Description: Bracket required for 2015 Ford F-150, Ford Fusion and, Ford Mondeo vehicles. Further Information Purpose: To support the connection between a GO device and the HRN-BS16T2 in certain Ford vehicles. |